This is a polished Limestone floor in the reception area of an office in the town of Wilmslow that had been installed around ten years prior. As you can see they were now in a poor state with ingrained dirt and cracks across the surface of some of the tiles.
Deep Cleaning Limestone Tile and Grout
The polished Limestone tiles needed to be cut back and refinished with a set of diamond encrusted burnishing pads however my first task was to clean the grout lines by applying a medium dilution of Tile Doctor Pro-Clean and scrubbing it in with a stiff narrow brush. I gave the grout a rinse with hot water and removed the now soiled water with a wet vacuum.
The next task was to start the burnishing process by running a course pad fitter to my rotary machine over each tile lubricated with a little water. The coarse pad removes the dirt from the Limestone and resultant slurry is washed away with more water and the wet vacuum. This process is repeated with the “medium” and “fine” polishing pads which restore the surface and build up the polish back on the tile.
Before moving onto the final polishing pad I tackled the large cracks in the tile by filling them with a colour matching resin. There could be a number of reasons for the cracks but typically it would indicate some sort of movement in the subfloor. A common cause is due to the concrete base was not being given sufficient time to dry out before being tiled over and shrinkage in the concrete as it dries caused movement.
Repairing and Sealing Limestone Tiles
Once the resin had dried I moved onto to apply the final “Super Fine” polishing pad which brings up the polish on the Limestone to that final deep level again using a little water and rinsing down afterwards.
Once the floor was dry it was then sealed with two coats of Tile Doctor Colour Grow which is an impregnating sealer which penetrates into the pores of the stone protecting it from within, it also had the added benefit of bringing out the natural colours in the stone enhancing the look of the floor.
Repairing and Polishing a Limestone tiled floor in Cheshire
These Sandstone floor tiles installed in the front room of a house in Bramhall were looking grey with no natural colour due to heavy soiling from family pets and muddy boots.
Cleaning Sandstone Floor Tiles
Cleaning the Sandstone was a straightforward process of applying a dilution of Tile Doctor Pro-Clean which is a commercial grade alkaline tile cleaning product designed for use on natural stone floors such as Sandstone, being an alkaline it doesn’t eat into the stone like acid cleaners. The solution was left to dwell for a while before working it into the stone with a rotary machine fitted with a black scrubbing pad. The resultant soiled solution was removed using wet vacuum and the floor washed down, there were still a few stubborn areas and the grout needed a good clean with more Pro-Clean and a stiff brush run along the grout lines.
Once I was happy with the condition of the floor any remaining cleaning solution was removed from the floor using a wet vacuum and the stone given a thorough rinse and left to dry.
The floor looked much improved however the customer on this occasion didn’t want the floor sealed which is a shame as a sealer really adds life to a floor and makes it easier to clean as a result this floor will soon discolour.
You can’t beat a Victorian Tiled Hallway it’s such a practical and obvious choice, unfortunately however this floor at a house in Chester had been neglected over the years and covered up with carpet that had been glued to the tile.
Restoring Victorian Floor Tiles
To remove the dirt, paint and carpet glue it was necessary to coat the floor in a strong dilution of Tile Doctor Remove and Go which as the name suggests is a powerful coatings remover that’s safe to use on tiles.
The solution was left to soak into the tiles in order to break down the glue and paint etc. before being scrubbed in using a rotary machine fitted with a black pad. This cleaned up most of the problems however there were a few stubborn areas on which we used a steamer to penetrate deep into the pores of the tile and lift out the stains. We then removed the soiled cleaning solution using a wet vacuum and give the floor a really thorough rinse.
Due to the age of the floor and house there was no damp proof installed under the floor and there was concern that even with a breathable sealer damp would become trapped under the tile, so we decided not to seal the tiles which is a shame as sealers do lift the appearance that much more. I think you will agree though the floor looks much improved.
Stained Victorian Tiled hallway floor cleaned and sealed in Cheshire
These beautiful Indian Sandstone tiles were installed on the ground floor of a house near Macclesfield and as you can see from the photographs had become heavily soiled which was masking the true natural colours in the stone resulting in a dark grey appearance.
Cleaning Indian Sandstone Floor Tiles
To get the tiles clean I let them soak in a strong dilution of Tile Doctor Pro-Clean for a while before working the cleaning agent in with a rotary machine fitted with a black scrubbing pad. The Pro-Clean also acts as a stripper so this process will remove any remaining sealer on the surface of the tile as well as the dirt.
Additionally all the grout lines were scrubbed by hand using more Pro-Clean and stiff scrubbing brushes. The remaining soiled solution was then removed from the floor using a wet vacuum and the tiles given a thorough rinse rinsed and left to dry completely with any stubborn marks re-treated using the same process.
Sealing Indian Sandstone Floor Tiles
Once I was satisfied the floor was dry it was sealed using Tile Doctor Seal and Go which is a topical sealer that leaves an attractive low sheen finish and smooth surface, it’s also a water based sealer so there is no smell.
Soiled Indian Sandstone floor tiles cleaned and sealed in Macclesfield
This Ceramic tiled bathroom with shower was installed at house Wilmslow and was overdue a refresh. You can see from the photographs below that the bathroom was looking tired and the tile and grout was discoloured with mould and acid build-up from washing products.
Cleaning Ceramic Tile and Grout
The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean which is a strong alkaline Tile and Grout cleaning product. The solution was decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.
The grout looked better but I was unable to shift some of the staining so we decided to apply a white Grout Colourant, it’s a time consuming process but I think you will agree it made a big difference. Additionally the grout colourant product we use also forms a barrier over the surface making the grout much easier to clean going forward.
The last step was to remove the silicone sealant from along the top of bath and replace with new.
This Indian Sandstone floor was laid in a large Kitchen, utility and WC in a house in Prestbury, Cheshire. It was cleaned professionally five years earlier and in that time the sealer had started to wear down and the floor had become dirty again. On top of that the rough nature of the Sandstone flagstones were shredding cleaning mops used to clean the floor so the customer decided it was time for a spring clean and arranged with us to have the floor cleaned and re-sealed.
Cleaning a Sandstone Tiled Floor
We cleaned the floor using Tile Doctor Pro-Clean diluted with 5 parts warm water and worked into the stone surface using a rotary machine fitted with a black scrubbing pad. The soiled solution was removed with a wet vacuum and floor rinsed with clean water using a spinning tool which applies water under high pressure and removes it at the same time. There were a few paint splashes evident so Tile Doctor Remove and Go was applied and left on the problem areas for about an hour which dealt with the problem and the floor washed down again with clean water applied with the spinner tool. This process had taken most of the day so we then left for the evening allowing the floor to dry overnight.
Sealing a Sandstone Tiled Floor
We came back the next day and tested the floor with a Stanley damp meter in a few different locations to make sure no dampness remained in the stone. The sandstone was dry so we proceeded to seal the floor with Tile Doctor Seal and Go which offers a good level of protection as well as giving a nice low sheen finish. Sandstone is fairly porous so it took five coats of sealer to fully seal the floor, also Seal and Go is a topical coating so this has also taken the roughness out of the stone and resolved their mop shredding issue. The floor was good to walk on several hours later.
This Terracotta tiled floor installed in a house in Wilmslow had become black and discoloured in areas due to the customer being badly advised on what sealer to use themselves; this resulted in the sealer staying tacky and turning black over time
Cleaning Discoloured Terracotta Tiles
To remove any remaining sealer and deep clean the Terracotta tile we used a strong dilution of Tile Doctor Pro-Clean worked into the floor with a buffing machine fitted with a black scrubbing pad. Pro-Clean is an ideal cleaner for natural floors due to its alkaline formula which doesn’t eat away at the tile like an acidic cleaner, it’s also very good for cleaning up grout however I find that’s best tackled manually using a stiff brush.
Last step in the process was to remove the soiled cleaning solution with a wet vacuum and then wash the whole floor down with clean water in order to neutralise it before sealing, we then left the floor so it could dry overnight.
Sealing and Colouring Terracotta Tiles
The next step was to seal the Terracotta floor and for this we applied Tile Doctor Seal and Go which is a water based sealer recommended for Terracotta floors, it provides stain protection and a low sheen that lifts the look of the floor. Seven coats were required due to the porosity of the Terracotta tile.
Cleaning and Sealing Terracotta Tiled Floor in Cheshire